Next: @sub and @sup: Inserting Subscripts and Superscripts, Previous: Inserting Accents, Up: Special Insertions [Contents][Index]
Use doubled single-quote characters to begin and end quotations: ``…''. TeX converts two single quotes to left- and right-hand doubled quotation marks, and Info converts doubled single-quote characters to ASCII double quotes: ``…'' becomes "…".
You may occasionally need to produce two consecutive single quotes;
for example, in documenting a computer language such as Maxima where
'' is a valid command. You can do this with the input
'@w{}'; the empty @w command stops the combination into
the double-quote characters.
The left quote character (`, ASCII code 96) used in Texinfo is a grave accent in ANSI and ISO character set standards. We use it as a quote character because that is how TeX is set up, by default.
Texinfo supports several other quotation marks used in languages other than English. Below is a table with the commands Texinfo provides for inserting quotation marks.
In order to get the symbols for the quotation marks in encoded Info
output, it is necessary to specify @documentencoding UTF-8.
(See @documentencoding enc: Set Input Encoding.) Double guillemets are also
present in ISO 8859-1 (aka Latin 1) and ISO 8859-15 (aka
Latin 9).
The standard TeX fonts support the usual quotation marks used in English (the ones produced with single and doubled ASCII single quotes). For the other quotation marks, TeX uses European Computer Modern (EC) fonts (ecrm1000 and other variants). These fonts are freely available, of course; you can download them from http://ctan.org/pkg/ec, among other places.
The free EC fonts are bitmap fonts created with Metafont. Especially for on-line viewing, Type 1 (vector) versions of the fonts are preferable; these are available in the CM-Super font package (http://ctan.org/pkg/cm-super).
Both distributions include installation instructions.
| Command | Glyph | Unicode name (point) |
|---|---|---|
| @quotedblleft{} `` | “ | Left double quotation mark (U+201C) |
| @quotedblright{} '' | ” | Right double quotation mark (U+201D) |
| @quoteleft{} ` | ‘ | Left single quotation mark (U+2018) |
| @quoteright{} ' | ’ | Right single quotation mark (U+2019) |
| @quotedblbase{} | „ | Double low-9 quotation mark (U+201E) |
| @quotesinglbase{} | ‚ | Single low-9 quotation mark (U+201A) |
| @guillemetleft{} | « | Left-pointing double angle quotation mark (U+00AB) |
| @guillemetright{} | » | Right-pointing double angle quotation mark (U+00BB) |
| @guilsinglleft{} | ‹ | Single left-pointing angle quotation mark (U+2039) |
| @guilsinglright{} | › | Single right-pointing angle quotation mark (U+203A) |
For the double angle quotation marks, Adobe and LaTeX glyph names
are also supported: @guillemotleft and
@guillemotright. These names are incorrect; a
“guillemot” is a bird species (a type of auk).
Traditions for quotation mark usage vary to a great extent between
languages (http://en.wikipedia.org/wiki/Quotation_mark).
Texinfo does not provide commands or configurations for typesetting
quotation marks according to the numerous traditions. Therefore, you
have to choose the commands appropriate for the language of your
manual. Sometimes aliases (see ‘@alias new=existing’) can simplify the
usage and make the source code more readable. For example, in German,
@quotedblbase is used for the left double quote, and the right
double quote is the glyph produced by @quotedblleft, which is
counterintuitive. Thus, in this case the following aliases would be
convenient:
@alias lgqq = quotedblbase @alias rgqq = quotedblleft
Next: @sub and @sup: Inserting Subscripts and Superscripts, Previous: Inserting Accents, Up: Special Insertions [Contents][Index]