Image Signature Verification

Glance has the ability to perform image validation using a digital signature and asymmetric cryptography. To trigger this, you must define specific image properties (described below), and have stored a certificate signed with your private key in a local Barbican installation.

When the image properties exist on an image, Glance will validate the uploaded image data against these properties before storing it. If validation is unsuccessful, the upload will fail and the image will be deleted.

Additionally, the image properties may be used by other services (for example, Nova) to perform data verification when the image is downloaded from Glance.

Using the Signature Verification

An image will need a few properties for signature verification to be enabled, these are:

img_signature
img_signature_hash_method
img_signature_key_type
img_signature_certificate_uuid

Property img_signature

This is the signature of your image.

Note

The max character limit is 255.

Property img_signature_hash_method

Hash methods is the method you hash with.

Current ones you can use are:

  • SHA-224
  • SHA-256
  • SHA-384
  • SHA-512

Property img_signature_key_type

This is the key_types you can use for your image.

Current ones you can use are:

  • RSA-PSS
  • DSA
  • ECC-CURVES
  • SECT571K1
  • SECT409K1
  • SECT571R1
  • SECT409R1
  • SECP521R1
  • SECP384R1

Note

ECC curves - Only keysizes above 384 are included. Not all ECC curves may be supported by the back end.

Property img_signature_certificate_uuid

This is the UUID of the certificate that you upload to Barbican.

Therefore the type passed to glance is:

  • UUID

Note

The supported certificate types are:

  • X_509

Example Usage

Follow these instructions to create your keys:

$ openssl genrsa -out private_key.pem 1024
Generating RSA private key, 1024 bit long modulus
...............................................++++++
..++++++
e is 65537 (0x10001)

$ openssl rsa -pubout -in private_key.pem -out public_key.pem
writing RSA key

$ openssl req -new -key private_key.pem -out cert_request.csr
You are about to be asked to enter information that will be incorporated
into your certificate request.

$ openssl x509 -req -days 14 -in cert_request.csr -signkey private_key.pem -out new_cert.crt
Signature ok
subject=/C=AU/ST=Some-State/O=Internet Widgits Pty Ltd
Getting Private key

Upload your certificate. This only has to be done once as you can use the same Secret href for many images until it expires:

$ openstack secret store --name test --algorithm RSA --expiration 2016-06-29 --secret-type certificate --payload-content-type "application/octet-stream" --payload-content-encoding base64 --payload "$(base64 new_cert.crt)"
+---------------+-----------------------------------------------------------------------+
| Field         | Value                                                                 |
+---------------+-----------------------------------------------------------------------+
| Secret href   | http://127.0.0.1:9311/v1/secrets/cd7cc675-e573-419c-8fff-33a72734a243 |

$ cert_uuid=cd7cc675-e573-419c-8fff-33a72734a243

Get an image and create the signature:

$ echo This is a dodgy image > myimage

$ openssl dgst -sha256 -sign private_key.pem -sigopt rsa_padding_mode:pss -out myimage.signature myimage

$ base64 -w 0 myimage.signature > myimage.signature.b64

$ image_signature=$(cat myimage.signature.b64)

Note

Using Glance v1 requires ‘-w 0’ due to not supporting multiline image properties. Glance v2 does support multiline image properties and does not require ‘-w 0’ but may still be used.

Create the image:

$ glance image-create --name mySignedImage --container-format bare --disk-format qcow2 --property img_signature="$image_signature" --property img_signature_certificate_uuid="$cert_uuid" --property img_signature_hash_method='SHA-256' --property img_signature_key_type='RSA-PSS' < myimage

Note

Creating the image can fail if validation does not succeeed. This will cause the image to be deleted.