Enabling/disabling ns-3 Tests and Examples¶
The ns-3 distribution includes many examples and tests that are used to validate the ns-3 system. Users, however, may not always want these examples and tests to be run for their installation of ns-3.
This chapter discusses how to build ns-3 with or without its examples and tests.
How to enable/disable examples and tests in ns-3¶
There are 3 ways to enable/disable examples and tests in ns-3:
Using build.py when ns-3 is built for the first time
Using ns3 once ns-3 has been built
Using the ns-3 configuration file once ns-3 has been built
Enable/disable examples and tests using build.py¶
You can use build.py to enable/disable examples and tests when ns-3 is built for the first time.
By default, examples and tests are not built in ns-3.
From the ns-3-allinone directory, you can build ns-3 without any examples or tests simply by doing:
$ ./build.py
Running test.py in the top level ns-3 directory now will cause no examples or tests to be run:
0 of 0 tests passed (0 passed, 0 skipped, 0 failed, 0 crashed, 0 valgrind errors)
If you would like build ns-3 with examples and tests, then do the following from the ns-3-allinone directory:
$ ./build.py --enable-examples --enable-tests
Running test.py in the top level ns-3 directory will cause all of the examples and tests to be run:
170 of 170 tests passed (170 passed, 0 skipped, 0 failed, 0 crashed, 0 valgrind errors)
Enable/disable examples and tests using ns3¶
You can use ns3 to enable/disable examples and tests once ns-3 has been built.
By default, examples and tests are not built in ns-3.
From the top level ns-3 directory, you can build ns-3 without any examples or tests simply by doing:
$ ./ns3 configure
$ ./ns3 build
Running test.py now will cause no examples or tests to be run:
0 of 0 tests passed (0 passed, 0 skipped, 0 failed, 0 crashed, 0 valgrind errors)
If you would like build ns-3 with examples and tests, then do the following from the top level ns-3 directory:
$ ./ns3 configure --enable-examples --enable-tests
$ ./ns3 build
Running test.py will cause all of the examples and tests to be run:
170 of 170 tests passed (170 passed, 0 skipped, 0 failed, 0 crashed, 0 valgrind errors)
Enable/disable examples and tests using the ns-3 configuration file¶
A configuration file, .ns3rc, has been added to ns-3 that allows users to specify whether examples and tests should be built or not. You can use this file to enable/disable examples and tests once ns-3 has been built.
When enabling disabling examples and tests, the precedence rules are as follows:
the –enable-examples/–disable-examples configure strings override any .ns3rc file
the –enable-tests/–disable-tests configure strings override any .ns3rc file
the .ns3rc file in the top level ns-3 directory is next consulted, if present
the system searches for ~/.ns3rc if the .ns3rc file was not found in the previous step
If none of the above exists, then examples and tests will not be built.
The maintained version of the .ns3rc file in the ns-3 source code repository resides in the utils directory. The reason for this is if it were in the top-level directory of the repository, it would be prone to accidental checkins from maintainers that enable the modules they want to use. Therefore, users need to manually copy the .ns3rc from the utils directory to their preferred place (top level directory or their home directory) to enable persistent enabling of examples and tests.
Assuming that you are in the top level ns-3 directory, you can get a copy of the .ns3rc file that is in the utils directory as follows:
$ cp utils/.ns3rc .
The .ns3rc file should now be in your top level ns-3 directory, and it contains the following:
# A list of the modules that will be enabled when ns-3 is run.
# Modules that depend on the listed modules will be enabled also.
#
# All modules can be enabled by emptying the list.
set(ns3rc_enabled_modules)
# A list of the modules that will be disabled when ns-3 is run.
# Modules that depend on the listed modules will be disabled also.
#
# If the list is empty, no module will be disabled.
set(ns3rc_disabled_modules)
# Set this equal to ON if you want examples to be run.
set(ns3rc_examples_enabled OFF)
# Set this equal to ON if you want tests to be run.
set(ns3rc_tests_enabled OFF)
# Override other ns-3 settings by setting their values below
# Note: command-line settings will also be overridden.
#set(NS3_LOG ON)
From the top level ns-3 directory, you can build ns-3 without any examples or tests simply by doing:
$ ./ns3 configure
$ ./ns3 build
Running test.py now will cause no examples or tests to be run:
0 of 0 tests passed (0 passed, 0 skipped, 0 failed, 0 crashed, 0 valgrind errors)
If you would like build ns-3 with examples and tests, use your favorite editor to change the values in the .ns3rc file for ns3rc_examples_enabled and ns3rc_tests_enabled file to be True:
# A list of the modules that will be enabled when ns-3 is run.
# Modules that depend on the listed modules will be enabled also.
#
# All modules can be enabled by emptying the list.
set(ns3rc_enabled_modules)
# A list of the modules that will be disabled when ns-3 is run.
# Modules that depend on the listed modules will be disabled also.
#
# If the list is empty, no module will be disabled.
set(ns3rc_disabled_modules)
# Set this equal to ON if you want examples to be run.
set(ns3rc_examples_enabled ON)
# Set this equal to ON if you want tests to be run.
set(ns3rc_tests_enabled ON)
# Override other ns-3 settings by setting their values below
# Note: command-line settings will also be overridden.
#set(NS3_LOG ON)
From the top level ns-3 directory, you can build ns-3 with examples and tests simply by doing:
$ ./ns3 configure
$ ./ns3 build
Running test.py will cause all of the examples and tests to be run:
170 of 170 tests passed (170 passed, 0 skipped, 0 failed, 0 crashed, 0 valgrind errors)