FPGA LOADABLE CODE GENERATOR FOR Icarus Verilog Copyright 2001 Stephen Williams $Id: fpga.txt,v 1.12 2005/09/19 21:45:36 steve Exp $ The FPGA code generator supports a variety of FPGA devices, writing XNF or EDIF depending on the target. You can select the architecture of the device, and the detailed part name. The architecture is used to select library primitives, and the detailed part name is written into the generated file for the use of downstream tools. INVOKING THE FPGA TARGET The code generator is invoked with the -tfpga flag to iverilog. It understands the part= and the arch= parameters, which can be set with the -p flag of iverilog: iverilog -parch=virtex -ppart=v50-pq240-6 -tfpga foo.vl This example selects the Virtex architecture, and give the detailed part number as v50-pq240-6. The output is written into a.out unless a different output file is specified with the -o flag. The following is a list of architecture types that this code generator supports. * arch=lpm This is a device independent format, where the gates are device types as defined by the LPM 2 1 0 specification. Some backend tools may take this format, or users may write interface libraries to connect these netlists to the device in question. * arch=generic-edif (obsolete) This is generic EDIF code. It doesn't necessarily work because the external library is not available to the code generator. But, what it does is generate generic style gates that a portability library can map to target gates if desired. * arch=generic-xnf (obsolete) If this is selected, then the output is formatted as an XNF file, suitable for most any type of device. The devices that it emits are generic devices from the unified library. Some devices are macros, you may need to further resolve the generated XNF to get working code for your part. * arch=virtex If this is selected, then the output is formatted as an EDIF 200 file, suitable for Virtex class devices. This is supposed to know that you are targeting a Virtex part, so can generate primitives instead of using external macros. It includes the VIRTEX internal library, and should work properly for any Virtex part. * arch=virtex2 If this is selected, then the output is EDIF 2 0 0 suitable for Virtex-II and Virtex-II Pro devices. It uses the VIRTEX2 library, but is very similar to the Virtex target. XNF ROOT PORTS NOTE: As parts are moved over to EDIF format, XNF support will be phased out. Current Xilinx implementation tools will accept EDIF format files even for the older parts, and non-Xilinx implementation tools accept nothing else. When the output format is XNF, the code generator will generate "SIG" records for the signals that are ports of the root module. The name is declared as an external pin that this macro makes available. The name given to the macro pin is generated from the base name of the signal. If the signal is one bit wide, then the pin name is exactly the module port name. If the port is a vector, then the pin number is given as a vector. For example, the module: module main(out, in); output out; input [2:0] in; [...] endmodule leads to these SIG, records: SIG, main/out, PIN=out SIG, main/in<2>, PIN=in2 SIG, main/in<1>, PIN=in1 SIG, main/in<0>, PIN=in0 EDIF ROOT PORTS The EDIF format is more explicit about the interface into an EDIF file. The code generator uses that control to generate an explicit interface definition into the design. (This is *not* the same as the PADS of a part.) The generated EDIF interface section contains port definitions, including the proper direction marks. With the (rename ...) s-exp in EDIF, it is possible to assign arbitrary text to port names. The EDIF code generator therefore does not resort to the mangling that is needed for the XNF target. The base name of the signal that is an input or output is used as the name of the port, complete with the proper case. However, since the ports are single bit ports, the name of vectors includes the string "[0]" where the number is the bit number. For example, the module: module main(out, in); output out; input [2:0] in; [...] endmodule creates these ports: out OUTPUT in[0] INPUT in[1] INPUT in[2] INPUT Target tools, including Xilinx Foundation tools, understand the [] characters in the name and recollect the signals into a proper bus when presenting the vector to the user. PADS AND PIN ASSIGNMENT The ports of a root module may be assigned to specific pins, or to a generic pad. If a signal (that is a port) has a PAD attribute, then the value of that attribute is a list of locations, one for each bit of the signal, that specifies the pin for each bit of the signal. For example: module main( (* PAD = "P10" *) output out, (* PAD = "P20,P21,P22" *) input [2:0] in); [...] endmodule In this example, port ``out'' is assigned to pin 10, and port ``in'' is assigned to pins 20-22. If the architecture supports it, a pin number of 0 means let the back end tools choose a pin. The format of the pin number depends on the architecture family being targeted, so for example Xilinx family devices take the name that is associated with the "LOC" attribute. NOTE: If a module port is assigned to a pin (and therefore attached to a PAD) then it is *not* connected to a port of the EDIF file. This is because the PAD (and possibly IBUF or OBUF) would become an extra driver to the port. An error. SPECIAL DEVICES The code generator supports the "cellref" attribute attached to logic devices to cause specific device types be generated, instead of the usual device that the code generator might generate. For example, to get a clock buffer out of a Verilog buf: buf my_gbuf(out, in); $attribute(my_buf, "cellref", "GBUF:O,I"); The "cellref" attribute tells the code generator to use the given cell. The syntax of the value is: <cell type>:<pin name>,... The cell type is the name of the library part to use. The pin names are the names of the type in the library, in the order that the logic device pins are connected. COMPILING WITH XILINX FOUNDATION Compile a single-file design with command line tools like so: % iverilog -parch=virtex -o foo.edf foo.vl % edif2ngd foo.edf foo.ngo % ngdbuild -p v50-pq240 foo.ngo foo.ngd % map -o map.ncd foo.ngd % par -w map.ncd foo.ncd --- $Log: fpga.txt,v $ Revision 1.12 2005/09/19 21:45:36 steve Spelling patches from Larry. Revision 1.11 2003/08/07 05:17:34 steve Add arch=lpm to the documentation. Revision 1.10 2003/07/04 03:57:19 steve Allow attributes on Verilog 2001 port declarations. Revision 1.9 2003/07/04 01:08:03 steve PAD attribute can be used to assign pins. Revision 1.8 2003/07/02 00:26:49 steve Fix spelling of part= flag. Revision 1.7 2003/03/24 02:28:38 steve Document the virtex2 architecture. Revision 1.6 2003/03/24 00:47:54 steve Add new virtex2 architecture family, and also the new edif.h EDIF management functions. Revision 1.5 2002/04/30 04:26:42 steve Spelling errors. Revision 1.4 2001/09/16 22:26:47 steve Support the cellref attribute. Revision 1.3 2001/09/16 01:48:16 steve Suppor the PAD attribute on signals. Revision 1.2 2001/09/06 04:28:40 steve Separate the virtex and generic-edif code generators. Revision 1.1 2001/09/02 23:58:49 steve Add documentation for the code generator.