Custom user models

Django’s built-in auth system provides a default model for user accounts, but also supports replacing that default with a custom user model. Many projects choose to use a custom user model from the start of their development, even if it begins as a copy of the default model, in order to avoid the difficulty of migrating to a custom user model later on.

In general, django-registration will work with a custom user model, though at least some additional configuration is always required in order to do so. If you are using a custom user model, please read this document thoroughly before using django-registration, in order to ensure you’ve taken all the necessary steps to ensure support.

The process for using a custom user model with django-registration can be summarized as follows:

  1. Compare your custom user model to the assumptions made by the built-in registration workflows.

  2. If your user model is compatible with those assumptions, write a short subclass of RegistrationForm pointed at your user model, and instruct django-registration to use that form.

  3. If your user model is not compatible with those assumptions, either write subclasses of the appropriate views in django-registration which will be compatible with your user model, or modify your user model to be compatible with the built-in views.

These steps are covered in more detail below.

Compatibility of the built-in workflows with custom user models

Django provides a number of helpers to make it easier for code to generically work with custom user models, and django-registration makes use of these. However, the built-in registration workflows must still make some assumptions about the structure of your user model in order to work with it. If you intend to use one of django-registration’s built-in registration workflows, please carefully read the appropriate section to see what it expects from your user model.

The two-step activation workflow

The two-step activation workflow requires that the following be true of your user model:

  • Your user model must set the attribute USERNAME_FIELD to indicate the field used as the username.

  • Your user model must have a field (of some textual type, ideally EmailField) for storing an email address, and it must define the method get_email_field_name() to indicate the name of the email field.

  • The username and email fields must be distinct. If you wish to use the email address as the username, you will need to write your own completely custom registration form.

  • Your user model must have a field named is_active, and that field must be a BooleanField indicating whether the user’s account is active.

If your user model is a subclass of Django’s AbstractBaseUser, all of the above will be automatically handled for you.

If your custom user model defines additional fields beyond the minimum requirements, you’ll either need to ensure that all of those fields are optional (i.e., can be NULL in your database, or provide a suitable default value defined in the model), or specify the correct list of fields to display in your RegistrationForm subclass.

The one-step workflow

The one-step workflow places the following requirements on your user model:

  • Your user model must set the attribute USERNAME_FIELD to indicate the field used as the username.

  • It must define a textual field named password for storing the user’s password.

Also note that the base RegistrationForm includes and requires an email field, so either provide that field on your model and set the get_email_field_name() attribute to indicate which field it is, or subclass RegistrationForm and override to remove the email field or make it optional.

If your user model is a subclass of Django’s AbstractBaseUser, all of the above will be automatically handled for you.

If your custom user model defines additional fields beyond the minimum requirements, you’ll either need to ensure that all of those fields are optional (i.e., can be NULL in your database, or provide a suitable default value defined in the model), or specify the correct list of fields to display in your RegistrationForm subclass.

Because the one-step workflow logs in the new account immediately after creating it, you also must either use Django’s ModelBackend as an authentication backend, or use an authentication backend which accepts a combination of USERNAME_FIELD and password as sufficient credentials to authenticate a user.

Writing your form subclass

The base RegistrationView contains code which compares the declared model of your registration form with the user model of your Django installation. If these are not the same model, the view will deliberately crash by raising an ImproperlyConfigured exception, with an error message alerting you to the problem.

This will happen automatically if you attempt to use django-registration with a custom user model and also attempt to use the default, unmodified RegistrationForm. This is, again, a deliberate design feature of django-registration, and not a bug: django-registration has no way of knowing in advance if your user model is compatible with the assumptions made by the built-in registration workflows (see above), so it requires you to take the explicit step of replacing the default registration form as a way of confirming you’ve manually checked the compatibility of your user model.

In the case where your user model is compatible with the default behavior of django-registration, you will be able to subclass RegistrationForm, set it to use your custom user model as the model, and then configure the views in django-registration to use your form subclass. For example, you might do the following (in a forms.py module somewhere in your codebase – do not directly edit django-registration’s code):

from django_registration.forms import RegistrationForm

from mycustomuserapp.models import MyCustomUser


class MyCustomUserForm(RegistrationForm):
    class Meta(RegistrationForm.Meta):
        model = MyCustomUser

You may also need to specify the fields to include in the form, if the set of fields to include is different from the default set specified by the base RegistrationForm.

Then in your URL configuration (example here uses the two-step activation workflow), configure the registration view to use the form class you wrote:

from django.urls import include, path

from django_registration.backends.activation.views import RegistrationView

from mycustomuserapp.forms import MyCustomUserForm


urlpatterns = [
    # ... other URL patterns here
    path('accounts/register/',
        RegistrationView.as_view(
            form_class=MyCustomUserForm
        ),
        name='django_registration_register',
    ),
    path('accounts/',
        include('django_registration.backends.activation.urls')
    ),
    # ... more URL patterns
]

Incompatible user models

If your custom user model is not compatible with the built-in workflows of django-registration, you have several options.

One is to subclass the built-in form and view classes of django-registration and make the necessary adjustments to achieve compatibility with your user model. For example, if you want to use the two-step activation workflow, but your user model uses a completely different way of marking accounts active/inactive (compared to the the assumed is_active field), you might write subclasses of that workflow’s RegistrationView and ActivationView which make use of your user model’s mechanism for marking accounts active/inactive, and then use those views along with an appropriate subclass of RegistrationForm.

Or, if the incompatibilities are relatively minor and you don’t mind making the change, you might use Django’s migration framework to adjust your custom user model to match the assumptions made by django-registration’s built-in workflows, thus allowing them to be used unmodified.

Finally, it may sometimes be the case that a given user model requires a completely custom set of form and view classes to support. Typically, this will also involve an account-registration process far enough from what django-registration’s built-in workflows provide that you would be writing your own workflow in any case.