Next: , Previous: , Up: Lexicons   [Contents][Index]


13.4 Letter to sound rules

Each lexicon may define what action to take when a word cannot be found in the addenda or the compiled lexicon. There are a number of options which will hopefully be added to as more general letter to sound rule systems are added.

The method is set by the command

(lex.set.lts.method METHOD)

Where METHOD can be any of the following

Error

Throw an error when an unknown word is found (default).

lts_rules

Use externally specified set of letter to sound rules (described below). The name of the rule set to use is defined with the lex.lts.ruleset function. This method runs one set of rules on an exploded form of the word and assumes the rules return a list of phonemes (in the appropriate set). If multiple instances of rules are required use the function method described next.

none

This returns an entry with a nil pronunciation field. This will only be valid in very special circumstances.

FUNCTIONNAME

Call this as a LISP function function name. This function is given two arguments: the word and the part of speech. It should return a valid lexical entry.

The basic letter to sound rule system is very simple but is powerful enough to build reasonably complex letter to sound rules. Although we’ve found trained LTS rules better than hand written ones (for complex languages) where no data is available and rules must be hand written the following rule formalism is much easier to use than that generated by the LTS training system (described in the next section).

The basic form of a rule is as follows

( LEFTCONTEXT [ ITEMS ] RIGHTCONTEXT = NEWITEMS )

This interpretation is that if ITEMS appear in the specified right and left context then the output string is to contain NEWITEMS. Any of LEFTCONTEXT, RIGHTCONTEXT or NEWITEMS may be empty. Note that NEWITEMS is written to a different "tape" and hence cannot feed further rules (within this ruleset). An example is

( # [ c h ] C = k )

The special character # denotes a word boundary, and the symbol C denotes the set of all consonants, sets are declared before rules. This rule states that a ch at the start of a word followed by a consonant is to be rendered as the k phoneme. Symbols in contexts may be followed by the symbol * for zero or more occurrences, or + for one or more occurrences.

The symbols in the rules are treated as set names if they are declared as such or as symbols in the input/output alphabets. The symbols may be more than one character long and the names are case sensitive.

The rules are tried in order until one matches the first (or more) symbol of the tape. The rule is applied adding the right hand side to the output tape. The rules are again applied from the start of the list of rules.

The function used to apply a set of rules if given an atom will explode it into a list of single characters, while if given a list will use it as is. This reflects the common usage of wishing to re-write the individual letters in a word to phonemes but without excluding the possibility of using the system for more complex manipulations, such as multi-pass LTS systems and phoneme conversion.

From lisp there are three basic access functions, there are corresponding functions in the C/C++ domain.

(lts.ruleset NAME SETS RULES)

Define a new set of lts rules. Where NAME is the name for this rule, SETS is a list of set definitions of the form (SETNAME e0 e1 ...) and RULES are a list of rules as described above.

(lts.apply WORD RULESETNAME)

Apply the set of rules named RULESETNAME to WORD. If WORD is a symbol it is exploded into a list of the individual characters in its print name. If WORD is a list it is used as is. If the rules cannot be successfully applied an error is given. The result of (successful) application is returned in a list.

(lts.check_alpha WORD RULESETNAME)

The symbols in WORD are checked against the input alphabet of the rules named RULESETNAME. If they are all contained in that alphabet t is returned, else nil. Note this does not necessarily mean the rules will successfully apply (contexts may restrict the application of the rules), but it allows general checking like numerals, punctuation etc, allowing application of appropriate rule sets.

The letter to sound rule system may be used directly from Lisp and can easily be used to do relatively complex operations for analyzing words without requiring modification of the C/C++ system. For example the Welsh letter to sound rule system consists or three rule sets, first to explicitly identify epenthesis, then identify stressed vowels, and finally rewrite this augmented letter string to phonemes. This is achieved by the following function

(define (welsh_lts word features)
  (let (epen str wel)
    (set! epen (lts.apply (downcase word) 'newepen))
    (set! str (lts.apply epen 'newwelstr))
    (set! wel (lts.apply str 'newwel))
    (list word
          nil
          (lex.syllabify.phstress wel))))

The LTS method for the Welsh lexicon is set to welsh_lts, so this function is called when a word is not found in the lexicon. The above function first downcases the word and then applies the rulesets in turn, finally calling the syllabification process and returns a constructed lexically entry.


Next: Building letter to sound rules, Previous: Lookup process, Up: Lexicons   [Contents][Index]